10 Facts About Fiat Panda Key Fob Replacement That Will Instantly Put You In A Good Mood
Reasons Your Fiat 500 Key Fob Won't Work
A key fob from Fiat 500 is a handy way to open the doors and begin the car. There are a myriad of reasons the fob could stop functioning. This includes a dead battery water damage, receiver modules issues, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local locksmith (click here to search for a Locksmith Search). Includes lock, unlock and trunk buttons.
Dead Coin Battery
A dead battery is the most common reason for your 500 key fob not functioning. Modern key fobs offer a limited range of operation and must be within only a few inches from the vehicle to work. If you are further away from your car and push the keyfob button it will not respond, and display the message "Key Fob Not Detected".
If this happens, replace the battery on your coin cell (Part number CR2032) with a brand new one from a trusted brand like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store or on the internet.
You can test the coin-cell battery by pressing the buttons while standing close to your Fiat 500. The parking lights should light up and the key fob should operate the lock and unlock switches.
If the fob's remote doesn't work after replacing the battery, it might have water damage that stops it from communicating with the receiver module in your car. Water damage can occur in a number of ways, ranging from small splashes to submerging your fob in salt water at the beach. If you think your fob was exposed to water, place it in a bag of rice to draw out the moisture. If this isn't working, you'll need to have your fob reprogrammed either by an auto locksmith or dealer.
Water Damage
Water damage can occur if you immerse the fob into the ocean or wash it in a machine. Saltwater is especially dangerous to the fob's circuit board which causes it to short out and eventually end up dying. If you get the fob wet, it's not an ideal idea but if you drop it in the water in a cup or forget to remove it from your pants pocket prior to running the washer Don't give up hope.
First remove the battery from the fob. Before replacing the battery, clean the electronic chip with isopropyl or similar products. Test the fob next to check if it's functioning. If the key doesn't function it could need to be reset. This is usually done by an auto locksmith or dealer.
If the key is newer and has never been programmed to your car, it will likely need to be replaced completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith will require the key to be cut to match your vehicle's ignition. The locksmith will also need to program your fob into the vehicle's system. This is a simple and cost-effective procedure that is usually completed the next day.
Receiver Module Issues
One of the simplest reasons your 500 key fob won't be functioning is because it's out of range. The remote usually has an area of 30 feet or less and if it's far from your car, it will not respond to your commands. You can solve this issue by moving the remote closer to your vehicle until it responds.
If your fob isn't working after you replace the battery for the coin, also known as a "button", "watch" or "button" it could be due to a problem with the internal circuit board. Reprogramming the fob usually resolves the issue. You can find the instructions on how to do this on the majority of vehicles by searching YouTube or checking out the owner's manual.
It is possible to replace the metal clips that hold the battery of your coin in place. If they loose tension it could hinder the battery from being seated properly and could cause the remote to malfunction.
In rare cases the fob could be out of sync with your vehicle because of software or hardware problems. You can fix this problem by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain instances, the software may also require reinstallation to your body control modules.
Interference
In addition to a dead battery on a coin The key fob may not be receiving or transmitting an signal due to interference. This can occur when the keyfob's location is in close proximity to a radio transmitter such as a cell phone or radar detector. Other reasons why the key fob might not function include a weak connection to the buttons, damage to the internal chip, or water damage.
If the key fob failed to work one day suddenly or even after trying everything you can do at home to resolve it e.g. You may have a faulty 500 receiver module if you've tried replacing the battery, reprogramming, or using an alternative key fob. The receiver module, located under the dashboard, picks up radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.
Luckily, there is fob programming to reset all on-board systems in your 500 device, including the key fob. Disconnect the battery 12 volt for about 15 minutes by removing the negative cable and then the positive cable. Then, reconnect the battery. This will remove any remaining electrical charge and restart the car's computers, which could help get your key fob working again. If the problem persists you should seek out an expert certified technician. They will be able diagnose the root of any issues.