10 Facts About Fiat Panda Key Fob Replacement That Can Instantly Put You In A Good Mood
Reasons Your Fiat 500 Key Fob Won't Work
A key fob for the Fiat 500 allows you to easily open doors and start your car. There are many reasons why the fob won't work. This could be due to a dead coin battery or damage to the receiver module, water problems, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote - like the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). Includes lock, unlock, and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob will not work is the battery is dead. Modern key fobs come with a limited range of operation, and should be within only a few feet from the vehicle to operate. If you are further away from your vehicle, and you press the keyfob button, it will not respond and display the message "Key Fob Not Detected".
If this occurs then replace the battery for your coin-cell (Part Number CR2032) by a brand new one from a reputable brand such as Panasonic Duracell or Energizer. You can usually find them in your local hardware store or on the internet.
You can test the coin-cell battery by pressing the buttons while standing close to your Fiat 500. The car should flash its parking lights and the key fob should be able to operate the lock and unlock buttons.
If your fob's key isn't working after replacing the battery, there might be water damage that has prevented it from communicating with the module in your vehicle. Water damage can happen in many ways, including simply splashing or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If that doesn't work, your fob is likely to need to be reprogrammed by an experienced auto locksmith or by the dealer.
Water Damage
Although the fob is equipped with rubber seals that keep water from the chip's electronic circuit, submerging it in the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then cease to function. In the event that you let your fob get wet, it's not an ideal idea, but if you drop it into an empty cup of water, or don't remember to remove it from your pants pocket before running the washing machine, don't give up hope.
Take the battery off first. Before replacing fiat doblo key clean the electronic chip using isopropyl or a similar product. Test the fob next to see if it is working. If the fob doesn't work, it may need to be changed. This is usually handled by an auto locksmith or dealer.
If the key is more recent and hasn't been programmed to your vehicle It will most likely need to be replaced completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith will need the key to be cut to match the car's ignition. The locksmith will also need to reprogram your fob into the car's system. This is a cost-effective and quick process that could be completed on the same day.
Receiver Module Issues
Your 500 key fob might stop working because it is out of range. The remote has a maximum range of 30 feet. Therefore, in the event that you are far from your car it won't be able to respond to your commands. You can easily remedy this by moving your remote closer to your vehicle until it responds.
If you've replaced the battery in your coin (commonly called"button" or "button" or "watch") and the fob isn't working it could be due to an internal circuit board issue. Reprogramming the fob typically resolves this problem. You can find the steps for the majority of vehicles on YouTube or in the owner's guide.
It is possible to replace the metal retaining clips that hold the coin battery in place. If they lose tension, they could stop the battery from sitting properly and can cause your remote to malfunction.
In rare cases the fob might be out of sync with your vehicle because of hardware or software issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain situations, they may need to install the software again in your body control module as well.
Interference
In addition to a dead coin battery The key fob may not be able to transmit or receive an signal due to interference. This could happen when the keyfob is located in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons the key fob might not work may be a lack of connection to the buttons or the internal chip, or water damage.
If the key fob stopped working one day out of the blue or after trying everything you can at home to fix it e.g. You may have a faulty 500 receiver module after you've tried replacing the battery, reprogramming, and using a spare key fob. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.
There's a simple method to reset the 500's in-board system including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will get rid of any remaining electricity and then restart the car's computer system, which could allow you to the key fob to function again. If the issue continues, you should consult an expert technician. They can identify the exact cause of issues.