Replacing a wood chair seat is a simple affair. It can be easily done at home as a weekend project. Here are some simple guidelines that will help you replace the seats of your wooden chairs at home. Step 1: Remove the Existing Seats Remove the existing seat of the chair with a powered screw driver. If the seat is upholstered, remove the existing upholstery and seat cushion as well. Take care while removing any staples or nails. Step 2: Cut out template for new seats With the wooden plank free now, take a tracing paper and trace the seat on to it. Cut out the traced bit and test fit on the chair seat. It should fit snugly, but not too tightly as you need to also consider a little space for the upholstery. Step 3: Cut out the new seat When you have the right shape and size on the tracing paper, trace the template back on the plywood sheet and cut it out with the help of a jigsaw. If you want you can also use a miter saw. Sand the sides of the cut ply wood seat carefully to ensure that there are no rough edges that can tear the upholstery or hurt somebody sitting on the chair.
Once ready, fit the new seat into the groove of your chair to check if it is the right size. Step 4: Fix foam on to the new seat Trace the seats on to foam sheets and cut similar shape as the seats with 2 inches extra. Now, place your new wooden seats in an open area and spray some wood glue on it. Apply the cut out foam sheets to the seat and press down firmly. Allow glue to dry as per manufacturers instructions. Step 5: Cut out fabric for reupholstering Once dry, turn the seat over and fix the extra protruding foam sheets with a staple gun. Now take your fabric and cut it using the same template of tracing paper that you used for the plywood seat. Now cut it in a similar shape but with 2 inches extra. These extra inches are important as these will be used to wrap the fabric around the edges and underneath the seat to give a clean look to your chair sheets. Step 6: Fix fabric on the new seats Once your fabric pieces are cut out, take a seat and wrap the front portion neatly with the fabric.
Carefully nail or staple it in the bottom of the seat. Once tightly fixed, pull the fabric neatly on to the back portion of the seat and fix it in a similar fashion with nails or staples. Similarly fix the other two sides as well. Trim all the excess fabric from underneath the seat. Ensure that you do a clean job. Step 7: Fit the new seat on the chair Fit your new seat on your chair and fix it with screws as was done previously.Seats and Stools has the Largest Selection of Replacement Seats and Backs for your home, office, restaurant, bar, or business. We carry an extensive product line with replacement seating, replacement chair or barstool parts, replacment frames, and replacement parts for Breuer chairs and Breuer barstools. Chrome Dinette Chairs: Metal Frame Chairs and Barstools: Wood Frame Chairs and Barstools: Breuer Chrome Chairs and Barstools: Bucket Barstools Bucket Chairs: Restaurant and Bar seating: Table tops and Table bases. We have many styles and sizes to choose from.
With a large in stock selection of Wood, Vinyl and Fabric we can match your exisitng decor or help you create a brand new look for your home or business. All Custom Made in the USA. Don't see what you need? Call our friendly and knowledgeable Customer Service team at (866)967-3287User ReviewedHow to Reupholster a Dining Chair Seat A high-impact way to improve or change the look of any chair with a removable seat is to recover the seat fabric. Whether you have pets and children, or just love to recycle old furniture, you'll appreciate this quick refurbishing technique. Unscrew the seat from the bottom of the chair. Remove the existing upholstery. Measure the width, length, and depth of the seat. Place the fabric wrong-side up on a flat surface. Trim the fabric so that there is enough all the way around to fold over the edge. Fold a flap of fabric along the straightest side and staple from the center working toward the corners. Repeat with the opposite side of the seat.under
Continue along the sides, still tugging firmly to make sure the fabric is tight over the top of the seat. Point the corner towards the center of the seat (along the diagonal). Fold one side down so that the folded edge runs along the diagonal. Fold the other side down in the same manner so that you now have a pleat along the diagonal. Trim any excess cloth. Stain protect the seats.outside Return seat to the chair and screw the base back in. Show more unanswered questions How to easily reupholster a chair video tutorial As you're stapling, take care not to block the screw holes with lots of fabric or staples. You can go through one layer of fabric easily, but staples are a problem. Old blankets that are no longer used can make a good batting for chair seats. A power stapler or staple gun is best for this task. A desk stapler won't be strong enough to penetrate the wood. You may wish to line tape the edges to prevent fraying of the cloth.
Buy extra fabric so you'll have some left over to make matching place mats, runners, or cushions to coordinate. To really tidy the underside up cut a piece of calico or lining material the same size as the underside of the seat make a 1 inch hem all around and staple this over base of the chair, so no fraying or unsightly wood can be seen. Alternative stapling approach: Start with a single staple in the middle of each left side (doing opposite sides first) and then add two staples (moving outward) on each side, rotating each time. This may help keep the stretch consistent across the edges of the chair, as inconsistent stretch is more likely to be a problem when stapling a whole side at once.Welcome back to Upholstery Basics, where we’ll be rolling up our sleeves and completing our first project together: a wrap-around seat. Of all seating, dining room chairs get the brunt of the abuse — a little vino here, red sauce there. If you’ve been glaring at those chairs and wondering how to give them that much-needed facelift, read on, and you’ll be transforming those eyesores into jaw-droppers in no time.
Read the full post on reupholstering dining chairs after the jump! Don’t forget to check out Upholstery Basics: Tool Time to learn more about the tools we’re using today. 1. Remove the seat from your chair frame by unscrewing the screws on the underside. If your seat drops into the frame, like mine, you may be able to pop it out without unscrewing it. Make sure to mark the orientation of the seat before removing. It may seem obvious, but it is imperative that we know which side is the front when we attach the fabric later. 2. Strip all of the old fabric, padding, staples and tacks off of the seat using your pliers and staple remover. Once you’re finished, you should be left with a wooden board. This is a good point to mark any screw holes, so you can avoid them as you attach new padding and fabric. 3. Flip the board upside down on top of the foam and trace the outside edge with a permanent marker. 4. Use the carving knife to cut out the shape. Don’t worry if the edges get a little ragged looking.
Just do your best to keep the blade straight up and down and not angled to one side or the other. 5. To create a slight domed shape to the seat, place a layer of cotton batting about an inch inside the edges of the board. Add extra layers if you’d like the crown of the seat to be more exaggerated. Just remember to make each additional layer of cotton slightly smaller than the one that precedes it. 6. Attach the foam to the board by stapling through the side of the foam and down into the wood. It’s best to work in opposites as you staple, so start with the back side and then move to the front. Then staple from the right to left side. Be careful not to push the foam back as you staple. We want the hard wooden edge to be padded, so it won’t show through the fabric. 7. Dacron will smooth out all of the imperfections and be the final layer of padding before the fabric. Once the foam is secured all the way around, tightly wrap Dacron around the edge and staple to the bottom of the board.
8. Trim off the excess Dacron gathered at the corners and around the bottom. 9. Now it’s time for the fabric! If you’re working with a pattern, decide where you’d like it placed on the seat. The rule of thumb is to place the top of the pattern at the back of the seat and the bottom of the pattern at the front of the seat. 10. To get started, staple the fabric at the back of the seat, but only put the staples in halfway by lifting one side of the staple gun up at an angle. These are called sub-staples and will allow you to pull them out very easily should you need to make adjustments. Once you’ve stapled the back, move on to the front. Then sub-staple the right and left sides. 11. Make a pleat in every corner by pulling the fabric from the sides around to the front and back. Fold under enough of the excess fabric to make the edges of the folds flush with the corners. Feel free to cut out bulky excess if you’re having trouble getting it all folded under the pleats, and use your regulator to get the fabric neatly tucked in.