Why We Are #1 New (32) from $92.19 See more product details Special Shipping Information: This product may not be available for 1 or 2 day shipping due to federal regulations that require it to ship via ground ship methods only. This product can only be shipped within the 48 contiguous states. Herculiner HCL1B8 Brush-on Bed Liner KitDetails3M 06654 36 mm x 55 m Automotive Refinish Masking Tape Add-on ItemFREE Shipping on orders over . Herculiner HCL0B7 Brush-on Bed Liner - Quart Herculiner HCL1G8 Gray Brush-on Bed Liner Kit Dupli-Color BAQ2010 Bed Armor DIY Truck Bed Liner with Kevlar Bed Armor - Quart Herculiner Brush-On Bedliner Kit - Black 10 x 7 x 8 inches 4.5 out of 5 stars #1,515 in Automotive (See top 100) #1 in Automotive > Exterior Accessories > Truck Bed & Tailgate Accessories > Bed Liners 10.1 pounds (View shipping rates and policies) Currently, item can be shipped only within the U.S. and to APO/FPO addresses.
This item is not eligible for international shipping. Manufacturer’s warranty can be requested from customer service. Click here to make a request to customer service. Herculiner brush-on truck bed liner kit includes the following: one gallon of ready-to-use protective coating, one application brush for tight spots and corners, two rollers for easy/even application, one roller handle, and one abrasive pad to prepare truck bed. It has polyurethane and rubber granule coating that is applied in just 3 easy steps to the bed surface using the rollers and brush included with the kit. When cured, it provides a durable skid-resistant protective coating. Because it can bond to virtually any surface or material, Herculiner can be applied to wood, metal, concrete, aluminum, asphalt, rubber, fiberglass, and most plastics, including PVC. 5 star72%4 star17%3 star5%2 star2%1 star4%See all verified purchase reviewsTop Customer ReviewsExcellent Bed Liner! I am quite happy with the results
Better Than Expected Results! See and discover other items: color bond Learn more about Amazon GiveawayI've always wondered why pickup trucks have painted beds. Hauling anything immediately scratches a brand-new truck bed. It's slippery as heck when wet. Of course, there are alternatives: Old trucks used to use wood, which rotted in a few years. You can buy a drop-in plastic bed liner, but it might rub off paint and trap moisture underneath, which leads to rust. I'm starting to think the best solution is an applied surface that's tougher than paint, like an epoxy concrete-floor coating. In the industry, these coatings are called spray-in bed liners, and there are several companies that will coat your bed. Using catalyzed-urethane-based polymers at 800 to 2000 psi, these liners are thicker and tougher than the driveway-applied roll-in liners—they're also considerably more expensive, with prices ranging from $400 to nearly $1000. This is a perfect DIY project: In only 4 hours, we did the job ourselves for about $50.
It's All in the PrepStart by washing the truck, paying special attention to getting the inside of the bed squeaky clean. Skip the wax setting at the quarter car wash, because the bed-liner material needs bare, clean paint to stick. Give the box a full day to completely dry. Find a shady, outdoor place. Trust me, you won't want to work indoors— this stuff stinks like dead dinosaurs when it's drying. Rubber gloves are a very good idea because it takes days to come out of your fingerprints. Use a leaf blower or a shop vac to clean the inside of the bed of any dust, leaves or water. If you've spilled any oil, ever, it'll need to be cleaned with mineral spirits. If there's any loose, peeling paint or rust on the sheet metal, you'll need to wire-brush, sandpaper or sandblast down to clean metal. Don't leave any loose rust around. Then blow out or vacuum the debris again. Prime the bare spots with a zinc-based primer, which you can spray from an aerosol can or even brush on.More Helpful HintsYou'll need to apply two coats.
Do both on the same day, but wait long enough, an hour or two, to allow the first coat to set up. Wait too long and the second coat may not bond properly. Achieving a consistent texture isn't trivial. It's a constant juggling act between having enough and too much material on the roller, rolling out what's there and backtracking to catch drips. Watch any inner corners, seams or fittings, as the liner material can sag several minutes later. No problem—just roller over it and catch the drips. Again, patience is the watchword. Use mineral spirits or lacquer thinner to clean up any spills.Remove the masking tape within 4 hours or so. Let the bed dry for about 24 hours, longer if the weather is cool. Be aware that the intense flat-black color of your liner will fade within a few months to charcoal gray. But then, so will the expensive spray-in liner.Brush On, Roller OnThe real secret to doing a proper bed-lining job is patience. Don't rush initial cleanup or proper scuff-sanding. Bonus: You can use leftover coating to touch up scratches periodically.
If so, don't forget to degrease the surface before recoating. 1. Once the bed is clean and dry and any bare steel is primered, mask off the bed tops, the tailgate, the hinges and the latch pins. Careful masking will considerably improve the aesthetics of the job. 2. Scuff the entire interior of the bed with either the kit's Scotch-Brite pad or some 150-grit sandpaper. Be thorough or the new liner will peel off in sheets later. 3. Here's an example of paint that's been scuffed properly. There will still be some shine, but you definitely need to leave a patina of scratches behind. I recommend a dual-action or orbital sander for most of the job and saving the Scotch-Brite for the inside corners. 4. Use solvent and fresh paper towels to degrease the bed. It's vitally important to get every inch. Change the toweling when it looks dirty. Wipe in only one direction, from the front of the bed to the back, to keep any greasy spots from migrating to the back. Needless to say, work out of doors for this step.