Can you believe that this gorgeous table was constructed from scraps of wood? To be exact, it was made with slats from wooden pallets and soft-wood that was reclaimed from another project. In just two days it went from a pile of material that some people might throw onto a campfire to a stunning table that would fit into any modern home. I captured the process of how my boyfriend, Josh Dudley of 123 Floor, made it and with his permission I’m sharing it here on Lovely Greens. Josh recently needed a new desk and after searching the classifieds he came up with a handful of cheap laminated pieces that were going for more than they were worth. Though he’s never built a desk before, the idea came into his mind to create one using some pallet wood we had stored in the garage. Josh’s years of experience as a floor layer even found their way into the table top design. The ‘Herringbone’ pattern is a common design that you’d see on modern floors but when I first spotted him laying the pallet slats in the same design my jaw nearly dropped.
I’ve honestly never seen a table top designed like that before. Especially in a DIY piece. The table measures 30″ in height, 4ft in width, and 2ft in depth. It’s constructed using mainly basic methods so even an amateur woodworker could recreate it. The first step is making the table top. Josh used an old piece of 1/2″ thick scrap pine as a base. With a pencil he marked out the final surface area of the table top but didn’t cut it until he’d laid out all the slats in their final design. Each of the wooden slats taken from the pallet are about 19″ in length and fit together just off-centre of the table top – he spent extra time beveling the edges of each piece with a sander but this step could be optional. What is not optional is sanding down the wood. Pallet wood is scruffy and covered in potential splinters so buff each surface area carefully. The angle that the slats are trimmed to at the sides is 45 degrees and a Mitre Saw was used to create the cut.
I’m sure there’s a hack to get around using this piece of equipment but if you can beg or borrow one off of someone it’s highly recommended. After the design was set out, Josh cut the slats and then placed them back onto the base. After they were all cut, sanded, and beveled, he cut the table top base and then glued the slats down. He also used a nail gun to secure each piece. Next he used 2×4″ soft wood to outline the underside of the table base flush with the edge. These add weight to the table so slightly smaller and lighter pieces might be more ideal. It’s what we had at the house though so that’s what he ended up using. Once those were attached with long screws, more pallet slats were used to create the skirting of the table top. They cover up the construction underneath and give the piece a more solid look. The corners were cut at 45 degree angles and Josh got a bit fancy and cut each slat’s other edge at the same angle so that it fits into the adjoining one.
Again wood glue and nail gun were the way they were fastened on but manually hammered in nails could be an option for those without a nail gun. Use very thin nails though. The legs are soft-wood pine and each is 27.5″ long. They’re glued and screwed in to the 2×4″ supports under the table top and then reinforced with angled pallet wood slats cut at 45 degrees on either side. Best seen in the below photo are the wooden connectors he built to attach the legs to one another for extra support. These are more pallet slats and are simply screwed into the legs. My contribution to his project is the suggestion to paint the legs with Blue Paint. I think it really makes the whole project stand out! The top of the table looks like the wood it is. There’s no intention to disguise the fact that its recycled pallet wood and it’s celebrated with a thin coating of Clear Wood Oil Finish to protect the top. It helps protect the surface from spills and adds a finer texture than paint or varnish.
One of the most exciting things to come out of this project (other than the table which I plan on liberating in the future) is a commission Josh received after pictures of his table first made their way online. Using this same method he’ll be creating a full floor for a couple here on the Isle of Man. He’s currently collecting pallet wood for the project but is still looking for more good sources. A full floor takes a lot of pallets but the finished floor will have the assurance of being 100% recycled wood. I’m sure it’s going to have a stunning, rustic look to it too! If you have any questions about the construction of this project, the best person to speak to is Josh. Message him on his Facebook page here. The Materials used for the table: For the top and sides: 27x Wooden slats from a pallet, each about 19″ long Table top base: 1x wooden board 2×4 foot Wooden stabilisers under the table top: 2×4″ soft wood For the legs: 4x squared pine pieces, 27.5″ long
For the angled leg braces and leg connectors: 6 more of the same wooden slats used for the table top Clear Wood Oil Finish to protect the top Blue Paint for the legs You’ll also need wood glue, thin nails, and screws to fit it all together Find Lovely Greens also on: Facebook, YouTube, Instagram, Twitter, and Pinterest You can make donations at your local Goodwill Store during business hours. You can also donate at the following attended donation centers and unattended donation centers. Attended Donation Centers are open seven days a week from 8:00 a.m. to 4:30 p.m., except for the Boston location, which is open seven days a week, 7:00 a.m. to 5:00 p.m. 905 Mass Avenue (Stop & Shop) 1010 Harrison Avenue (Roxbury. Open daily 8:00 a.m. to 5:00 p.m.) 299 Chelmsford Street (Stop & Shop Plaza) 211 Sudbury Road (Crosby's Market) 36 Bedford Street (Behind Walgreens) 115 Rumford Ave (Open Monday-Saturday 7:30 a.m. to 2:30 p.m.) 757 Turnpike Street (Super Stop & Shop.
19 Howley Street (Stop & Shop Plaza) 1342 Main Street (Home Goods) 509 Boston Post Road (Behind Shaw's) 450 Paradise Road (Stop & Shop Plaza) 1100 Lexington Street (Waltham Plaza. 169 Great Plain Avenue (Open during town's Transfer Station hours and for Wellesley residents only.) 400 Cambridge Road (Whole Foods Market) Unattended Centers (Municipal Recycling Centers) Please contact municipal offices for hours of operation. You must have a town sticker to access these sites. Theo F. Smith Road South St. Transfer Station Boston Post Road (Rt. 20) Donations are critical to Goodwill’s ability to provide much-needed services to the local community. When deciding what to donate to Goodwill, please take a minute to review the following lists before bringing your items to one of our convenient donation sites. To estimate the value of your donation, please go to http://www.irs.gov/pub/irs-pdf/p561.pdf. Please note that according to the Pension Reform Act of 2006: Donated items must be in good condition in order to claim a deduction, and a qualified appraisal must accompany claims greater than $500.
The law does not define "good condition," and the IRS says defining the condition and value of the items is the responsibility of the donor. To protect your generous donation from vandalism or theft, we ask that you please donate during posted hours. Goodwill accepts items like these in good condition: Bedspreads, blankets, curtains, tablecloths, decorative pillows Books, records, tapes, CDs, DVDs Clothing, belts, scarves, ties, pocketbooks Cookware, dishes, pots and pans Housewares and decorative items What we do not accept: Goodwill is unable to accept the following items (due to the high cost of disposal, safety concerns, and/or strict government regulations): Any items in need of repair or with missing parts Auto parts or auto accessories Baby furnishings (strollers, car seats, high chairs, cribs) Camping equipment containing gas, oil or butane Furnaces or wall heaters Furniture in need of repair or reupholstering
Gas-powered garden tools (lawn mowers, weed whackers, etc.) Hazardous materials including, but not limited to, paint, oil, cleaning products, batteries, and extinguishers Large appliances (washers, dryers, stoves, dishwashers, refrigerators) Mattresses, box springs, waterbeds, bed frames, futons, futon frames, pillows Plumbing or building supplies (cabinets, doors, etc.) Recyclable consumer materials (aluminum, glass, plastic, corrugated material) Reconnect is a residential computer recycling program that offers you an easy convenient and responsible way to recycle your used computer equipment. You can drop off any brand of used computer equipment at participating Goodwill donation centers in your area. It's free, and you'll get a receipt for tax purposes. What's more, you'll be helping protecting the environment and benefiting your community at the same time. What can I recycle? **Residents are advised to remove all personal data from their hard drives before donating a computer or hard drives.