Waikele Self Storage is now a StorQuest Self Storage location SELF STORAGE FINALLY ARRIVES IN WAIKELE! Three Kama’aina businessmen have developed a portion of the Waikele “caves” into conventional self storage units for public rental.. They had a vision that these large caves could provide value priced self storage for Oahu Honolulu Waikele consumers. Only 2 minutes from Waikele Shopping Center on Oahu near Honolulu, the former Navy ammunition storage facility was created during World War II. Each of 120 cave-like compartments was dug out of solid rock into the lower portion of Kipapa Gulch to securely store weapons and munitions. Used from 1943 until the mid 1980’s, the caves were cleared out and cleaned by the Navy when they sealed them all in 1987. Made available only a few months ago, each cave has a loading dock and ramp leading to secure entrances made of thick steel. Inside, Waikele Self Storage has installed brand new customer storage lockers of various sizes.
Each locker is equipped with steel walls and a locking steel rollup door. All cave interiors are well lit, with concrete floors, natural year round climate control and easy access through the wide aisles. Waikele Self Storage provides dollies and carts for easy loading and there is plenty of parking. Waikele Self Storage is locally owned and operated and offers the best customer service and conveniences available. We look forward to doing business with you.EURO SHUTTERS INDUSTRIES opened its door for supply, installation, maintenance and service of Roll up Doors in Marikina See more119 people like this1 person has been here of 73results123NextDidn't find what you were looking for?magnifying glass • If you typed the page address in the Address bar, make sure that it is spelled correctly. • Use the navigation bar on the left to find the link you are looking for. • Click the Back button to try another link. The page you requested cannot be found. The page you are looking for might have been removed, had its name changed, or is temporarily unavailable.
High speed, hydraulically-powered operator option (patent pending) Get the speed and power only a hydraulic operator can offer. A two horsepower electric motor runs a hydraulic pump and supplies pressure to a hydraulic wheel motor. System comes complete with a safety brake to lock door in position in the event of hydraulic pressure loss. System is shipped fully assembled, wired, plumbed and tested. Maintenance free operation in all climates. Strong, welded-steel frame assures long life Hi-Fold Door panels are built with double, rectangular, structural-steel tubes at the center hinge line (2" x 4" on doors to 46’ wide; 2" x 6" on wider doors) and 1 1/2" or 2" square structural-steel tubing, depending on door size, for the remainder of the frame. Doors over 46’ wide are made in two sections that bolt together through super-strong, 1/2" steel butt-plate joints. Strong mounting hinges (4,5,7 or 9, depending on door width) are welded to the top rail. Powerful drive system assures dependable operation
Name brand electric motor (1 hp to 2 hp depending on door size) with worm-gear speed reducer connected to a torque-free, 2" diameter drive shaft by a double jack-shaft and heavy-duty roller chain opens the Hi-Fold Door. Motor and electrical systems are mounted 18" or more above the floor on the side of the door for easy maintenance and to meet the National Electrical Code, Section 513 specifications, pertaining to aircraft hangars. Pulley-free design minimizes cable wear and promotes safe operation Hi-Fold Doors are delivered completely rigged. 7/32" lift cables with a 5 to 1 safety factor are secured to top rail of the door and wrap around large diameter drums on the full-width drive shaft as the door rises. Cable guards cover the lift drums to protect people, clothing, and pets. Lift cable "poppers" (inset photo) automatically push the center hinge away from the building as the door rises. Automatic jamb latches optional (U.S. Patent No. 5,343,923) Patented automatic, "knee-action" jamb latches release the Hi-Fold Door when opening, and grab latching hardware on your building when closing, to pull it tight against the jambs.
An optional full-width safety edge reverses the door if an obstacle is encountered. Automatic cane-bolt, on doors over 40' wide, secures and releases the door at the floor. Optional radio control lets you operate the door from outside your building. Optional remote antenna increases transmitter range. Free Standing Door Frame Jambs and header support for door operation. This frame is ideal when building structure is inadequate or questionable. Jambs can be anchor bolted to concrete or set below grade on a footing. Header to be attached to building to assist with horizontal loads. Welded-steel trusses withstand strongest wind loads All Hi-Fold Doors receive one to three inside trusses. Made of heavy-gauge, steel tubing with angle-iron webbing, they provide extra strength to control wind-load deflection when the door is closed and to help the "dogleg" center hinge eliminate sag when the door is open. Doors over 26' wide receive full-width trussing in the middle of the top and bottom panels, plus the bottom truss, which holds the drive system.
Smaller doors require the bottom truss only. Convenient "open-close-stop" push-button control 24-volt system mounts at any handy location inside the building near the Hi-Fold Door. Normally does not require conduit (depending on local codes), which allows pre-wiring and flexible cable on the building frame. For safety, the operator must push the "stop" button before changing door direction. Can be stopped and started at any midpoint. Electric brake is standard. Comes factory-wired for 110-volts on 1 hp doors; 220-volts on 1.5 hp& 2 hp doors. Radio remote control is optional. Auxiliary arms provide high clearance advantages (U.S. Patent No. 4,609,027) Patented auxiliary arms on each side of the Hi-Fold Door enable it to open completely while requiring less overhead space. As the door rises, smooth rolling steel wheels on the arms contact the optional reinforcement rails on both jamb posts to provide strong, dependable support. Double-strength center hinge, welded-steel wind trusses and strong, vertical joints combine with the auxiliary arms to hold the door in the horizontal, sag-free, full position.
Walk doors and windows are optional Add to the convenience and appearance of your Hi-Fold Door by ordering walk doors for easy access to your building and/or windows for natural lighting inside. Choose from a wide variety of attractive styles and sizes. Framed openings for the door and windows you desire are welded into your Hi-Fold Door panels at the factory. Walk door and windows are then easily mounted in place after the Hi-Fold Door is installed on your building. Double-strength center hinge design eliminates sagging Unique, "dogleg" center hinge design, formed by the rectangular-steel members on both the top and bottom Hi-Fold Door panels, provides a "double-strength" beam that virtually eliminates sagging in the full-open position. This strength, combined with the strength of the welded-steel trusses on the inside of the door, provides even greater resistance to wind-load when the door is closed. A floor cane-bolt on all doors over 40' wide further resists wind-loads.
Single location crank latch (patent pending) Mounted inside building on door, these self-adjusting latches tightly draw and secure Hi-Fold Door against jambs to protect against thieves and bad weather. Electrical interrupt supplied to guard against damage if locks are not fully released prior to operation. A durable bottom weather seal adjusts to floor irregularities; 9" and 12" top door seals are optional.& 2 hp doors. Shipped fully assembled for fast, easy installation Hi-Fold Doors are custom built for every job and shipped to your building site completely assembled and wired. When you're ready to install, simply hoist the door into place over the opening, fasten the hinges to the building header, adjust the high clearance auxiliary arms and connect the wiring to your power source. Except for applying the skin, your Hi-Fold Door is ready to operate. Retrofit installations retain full door opening clearance Hi-Fold Doors are ideal for replacing worn-out or hard-rolling sliding doors, troublesome overhead doors and closing doorless opening on existing buildings without changing building design.