Published on July 5th, 2013 | Reviews and Difference Between Semi Transparent Stains There are many different exterior stains that you can use. Below is our worst of list and best of list. They all have claims that their product is the best. There are so many different types of stains and even difference in opinions on how the stain should protect the deck or fence. Some stains work in weather in some states and some work in all weather. Its a complicated issue to chose the correct semi transparent stain. Read carefully and make your decision. If you are in the Indianapolis Metro area and need of deck staining or fence staining please contact Grants Painting. Three Basic Oils Used In Semi Transparent Exterior Stains(Oil Based AND Water Based) There are four types of semi transparent stain oils. Even waterborne stains have oils in them(at least any of them worth using). Most stains use a combination of these oils. A product that is only one type of oil is typically not your best option.
Non-Drying Oil Stainnon-drying oils Drying Oils– Drying oils dry to a hard film known as a polymer. SHOULD NOT be used in areas that receive hail or any other hail type damage like a lawn mower that sometimes kicks up rocks. Stains with high amounts of drying oils such as boiled linseed oil can be destroyed in a good hail storm and very difficult to repair. Behr stains have a high amount of drying oils. Semi Drying Oils– Semi drying oils are the best option in most environments because they protect and penetrate while not cracking and not rinsing off in a hard rain. Best products and Worst products – Please suggest more Wolmans Semi Transparent Stain (DuraStain) – – This product is much like the Behr stain and is another film forming product. Pittsburg Ultra Semi Transparent Stain – – This is a stain, available at Menards, that we used very much in our earlier years. It is an excellent stain but ust not be applied too thick. That is the case with every semi transparent stain.
Cabot Stains- – These stains have one and only one good benefit… Cabot stains are easy to touch up missed spots and its very easy to keep a wet edge. However when a water based stain is formulated for idiot proof application its going to fall short in every other category. Its also very hard to clean up. TWP 1500 – Read our review about this great stain Here. Film Forming Stain Vs. Non Film forming Film forming stains are not recommended in any environment by Grants Painting. The film can be damaged by impact of a weed wacker, mowers kicking up rocks, and most of all hail! We recommend stains that soak in totally and protect the wood from inside. How To Get Any Water Based Stain To Soak In More Water based stains soak in better in cooler temperatures early in the morning. The wood should also be not too dry. Spraying it down a few hours before can help but be careful that water built up between the planks and the 2×4 will cause drips when the stain is applied.
Also too much wetness and the wood wont be able to pull in any more liquid so the stain won’t penetrate. Usually a good wet down right before the sun goes down will get this done for an early morning application. Achieve the look you desire and lasting protection that your wood deserves. Pittsburgh Paints & Stains delivers a full range of finishes, from enhancing your wood’s natural beauty with clears and toners to the added durability of semi-transparent and solid color stains.Pittsburgh Paints & Stains® Ultra Advanced Exterior Stain (Solid Color) Pittsburgh Paints & Stains Ultra Advanced Solid Color Stain is a premium-quality stain and waterproofing sealant in one product. Rich, opaque color hides signs of aging while allowing the natural texture of wood to show, making it ideal for older wood. A self-priming, 100% acrylic stain, Pittsburgh Paints & Stains Ultra Advanced Solid Color stain delivers our best protection in a solid color stain. Browse Stain Prep Products
Stain and sealant in one both protects and beautifies with a single brush stroke Advanced two-way waterproofing protection Ultra UV premium protection guards against sun damage Provides a mildew-resistant coating Low temperature application down to 35°F Surface Preparation: Surface must be clean, dry and free of all dust, dirt, mildew, oil, loose wood fibers and other contaminants. Remove loose, peeling stain or paint by sanding, scraping or wire brushing. Use an exterior wood cleaner to prepare new wood prior to coating, and to clean and restore weathered, dirty surfaces and remove mildew stains. After rinsing, allow wood to dry. Application: DO NOT THIN. Stir thoroughly and often during use. Apply to a small area and allow to dry to ensure acceptable appearance. Intermix containers to ensure color uniformity. Apply two thin coats with a high quality brush, roller, paint/stain pad or by spray equipment. When rolling or spraying, always backbrush for best results.
Some colors, or a drastic color change may require an additional coat to achieve a uniform finish. To help avoid lap marks, apply to only a few boards at a time, and maintain a wet edge. Application Temperature: Apply when no precipitation is expected for 24 hours, and when air and surface temperatures are 35°F to 90°F (2°C to 32°C) and will remain above 35°F (2°C) for the next 24 hours. Avoid staining in direct sunlight or on hot surfaces. Drying Time: Normally dries to touch in 30 minutes when applied in temperatures of 50°F (10°C) to 85°F (29°C). Allow 2 to 4 hours between coats or before recoating. High humidity or low temperature application may prolong drying and recoating times. Allow 24 to 48 hours of drying time for light foot traffic or furniture placement. Newly stained surfaces should be allowed to cure 30 days before washing. Cleanup: Clean brushes and tools with warm, soapy water.Pro ErosionErosion ControlGrow Grass From SeedGrowing GrassQuickgrass ProBiodegradable MeshGrass EmbeddedMesh BlanketControl BlanketForwardHaving trouble growing grass?