Below is information to help you program your Garage Door Operator remote control or outside keypad. If you need additional help, feel free to give a call for assistance or to schedule a service call to program for you. CHAMBERLAIN / LIFTMASTER / SEARS CRAFTSMAN GARAGE DOOR OPENERS Programming 971LM and 973LM, 371LM and 373LM Security Plus Transmitters LIFTMASTER AND SEARS CRAFTSMAN WIRELESS KEYPADS 976LM, 377LM Security Plus and 66LM Wireless Keyless Entry Systems The square smart button is located on the side or the back of the motor head, and is colored red, green, amber, orange, or purple. It is directly under the #1 wire terminal screw. Programming Genie Intellicode Remote Transmitters ** To erase all Intellicode remotes and wireless keyless entry, hold down on the learn button until the indicator light stops blinking, then proceed to Step 2. These transmitters work by matching the settings on the internal code setting switches with the same set of switches in the receiver on the garage ceiling.
The receiver is located either behind the light lens of the Genie garage door opener motor head, or inside an external small rectangular box on the ceiling, which is connected to the motor head by a set of wires. Note: the frequency of the transmitter must be the same frequency as the receiver on the ceiling for it to work. Genie has been making the 390 MHz frequency exclusively for the last 15 years. These garage door opener transmitters have 2 smaller switches to the right of the internal Code Setting Switches. The small right switch should be set according to how many Code Setting Switches in your receiver (either 9 or 12). The small left switch is for programming purposes. To program a button for one of your doors, follow the instructions below: Genie Garage Door Opener Wireless Keypad Model GPWK-12, GWK (works with remotes having 9 or 12 internal code setting switches. Keypad is black with a slide-up cover showing the Genie logo only) This keyless garage door opener entry pad works with Genie transmitters using 390 MHz frequency.
It is NOT compatible with Genie Intellicode transmitters (if your keypad has Intellicode printed on the cover, go to the next set of programming instructions below). The Door Code in the Step-By-Step Procedure at right is determined by the internal code switches inside your transmitter and the accompanying chart. Determine the settings of the first 3 switches and write down the corresponding number from the chart. Continue with the next 3 switches and its corresponding number, and so on, until the last set of 3 switches. You should have 3 or 4 Door Code numbers. Door Code in Step #4: ____ ____ ____ ____ Model 1: Intellicode Model GWKIC, ACSDG (black with slide-up cover and the word “Intellicode” printed on the cover) GWKIC, ACSDG, Two Part, Step-By-Step Programming To Reset the Intellicode Wireless Keypad To Program the Intellicode Wireless Keypad NOTE: If red indicator light does not blink, it is not taking the programming steps. Check the 9 volt battery under the keypad numbers.
To access, press inward, under the number pad lip while sliding downward to expose the battery. Press the Receiver Learn Code button on the Power Head Receiver of your Genie Garage Door Opener. This small black button is located behind the light lens at the motor head and is nearest the floppy 6 inch antenna wire that protrudes from the power head. When pressed, a radio signal indicator will start blinking red for 30 seconds. Adding More Doors to Keypad: With most Genie units, remove the light lens globe to expose the Learn Button on the motor head. The learn button is sometimes located on the back of the unit, or with Accelerator openers, it is under the light lens near the hinge of the lens globe. Always locate the floppy antenna wire first. The Learn Button can be found not far from this antenna. See Troubleshooting Guides for Accelerator photo. Intellicode Model GWKP (off-white with flip-up cover) Programming Instructions for the GWKP Genie garage door opener keyless entry involves following the two sets of steps below:
Find the Learn Code Button and the LED indicator light on your Genie motor head inside the garage. It is usually behind the light lens and close to the floppy antenna wire. If your Door Opener does not have an antenna, you have an External Receiver. The External Receiver cover must be removed to access the Learn Code button and the indicator LED. Follow Steps 1 through 3 outlined below: Multiple Genie Garage Door Opener Programming for GWKP- All garage doors will use the same PIN: HOMELINK IN-CAR REMOTE PROGRAMMING INSTRUCTIONSYour garage door is the largest entryway into your home, and you likely use it every day. An automatic entry system allows convenient, safe, and easy access to your home. Precision Door Service of Orange County offers our own line of garage door openers, along with top manufacturers such as Chamberlain, Genie, and LiftMaster. Our trained technicians can install all models of garage door openers and remotes, or repair your opener if it is malfunctioning.
There are four main types of garage door openers. Precision Door Service can help you choose the right type for your door and lifestyle. The energy-efficient, DC-powered operator that runs at an AC-equivalent speed. DC drive motor with soft-start and soft-stop for smooth, quiet, long-term reliable performance. Advancements in garage door appearance and productivity are putting a new spin on home improvement options. With laser pointers, you can park in the right spot in your garage every time. No more bashed-in bumpers! If you are experiencing problems with your garage door opener or remote, Precision Door Service of Orange County offers repair services from our qualified repairmen. We offer same day service and 24/7 emergency repair services. In some cases, our technicians may recommend replacement of your garage door opener. In general, you should replace your garage door opener if: If you are experiencing problems with your garage door opener, or want to upgrade your current opener, contact Precision Door Service of Orange County, CA today for a free quote.