The Linear GoControl Garage Door Opener (GD00Z-4) lets you remotely open and close almost any sectional garage door. With both audible and visual warnings that trigger prior to remotely activated door movement, the GD00Z-4 meets UL 325-2010 safety requirements. The GD00Z-4 also includes a wireless tilt sensor that attaches to the inside of the garage door and reports whether it is "open" or "closed." This Z-Wave garage door opener provides peace of mind, convenience, security, and safety. Connect the GD00Z-4 with SmartThings to open or close your garage door from anywhere—perfect for allowing entry for a handyman, or for closing the door if you forgot to. You can also set up automations to open or close the garage door as you arrive and leave home. The GD00Z-4 will act as a Z-Wave repeater for other Z-Wave devices on your SmartThings network. 1. Install the tilt sensor The GD00Z-4 includes a wireless tilt sensor that attaches to the inside of the garage door. The tilt sensor reports “open” or “closed” status to SmartThings.
Consult the GD00Z-4 installation instructions, which can be downloaded from the link at the bottom of this article, to install the tilt sensor. 2. Pair the GD00Z-4 with the SmartThings Hub First, connect the GD00Z-4’s power cord and plug in the device within 10 feet of the SmartThings Hub. Next, in the SmartThings mobile app: 3. Mount and connect the garage door opener Consult the GD00Z-4 installation instructions, which can be downloaded from the link at the bottom of this article, to mount the GD00Z-4 and to connect its wires. If you need help installing the GD00Z-4, contact a certified electrician. If the GD00Z-4 was not discovered, you may need to reset, or “exclude,” the device before it can successfully connect with the SmartThings Hub. To do this in the SmartThings mobile app: After the app indicates that the device was successfully removed from SmartThings, follow the first set of instructions above to connect the Linear GoControl Garage Door Opener.
With the Linear GoControl Garage Door Opener (GD00Z-4) and a simple Routine, you can configure your garage door to open and close automatically based on activity, time of day, or other events. From the SmartThings mobile app: Depending on how you configured the Routine, the garage door will automatically open or close when certain events occur. You can also manually trigger the Routine by tapping its icon from the main Routines view. If the Linear GoControl Garage Door Opener (GD00Z-4) is connected but not operating as normal, you may need to remove the device and reconnect it with the SmartThings Hub. To remove the device via the SmartThings app: For technical specifications and product details, visit our Works With SmartThings page here.A multi-function door control is necessary for setting light controls. A multi-function door control has a Light, Lock and a pushbutton to open and close the garage door. If you do not have a multi-function door control you will not be able to permanently change these light options.
Refer to your manual to verify if your opener has these options. NOTE: If you do not have a multi-function door control and wish to have the lights stop turning on while you are doing yard work or cleaning the garage, you can open your door and before it is fully open, press the door control to stop the door from opening completely. This will temporarily disable this feature until the system operates again. Please close and open your door again before entering or exiting the garage with your vehicle to eliminate any damage. Press the Light button to turn the opener light on or off. It will not control the opener lights when the door is in motion. If you turn it on and then activate the opener, the light will remain on for 4-1/2 minutes. Press again to turn it off sooner. The 4-1/2 minute interval can be changed to 1-1/2, 2-1/2, or 3-1/2 minutes as follows: The Lock button is also used to lock out the hand held remote controls. Once you have finished setting the light timer, ensure the light inside the door control is glowing steadily.
If the light is flashing, the "Lock" feature has been engaged. The opener light will turn on automatically when a person enters the garage. When a person walks in front of the door control, the light will turn on for a set amount of time between 1-1/2 to 4-1/2 minutes, then shut off. This feature works by detecting body heat using Passive Infrared motion sensing (PIR). To disable this feature, push the motion sensing button or flip the switch on the side of the door control. It is recommended that the motion sensor be disabled when using the opener lights as work lights. Otherwise they will turn off automatically if you are working beyond the sensor's range. Program 3-button remote to control the lights In addition to operating the door, you may program the remote to operate the lights.Garage door opens 6 inches then stops It is an older (9/99) 1/2 HP Craftman model. Been working fine since we got the house, but today it would only open about 6 inches then stop.
The most o got it to open was about a foot. I have tried adjusting the limit screws and nothing! If i disconnect the opener from the door, i can open it by hand. The, when in the up position if i hit the button the traveler will open all the way until it reconnects. The door shuts fine, but then won't open again. I have the same problem I have the exact same problem and it is driving me crazy! I don't want to buy a new one if I do not have to. Disconnected from the opener, the door opens easily by hand. I checked the rails the rollers, and the springs have been replaced a couple years ago, so the problem is not the door. also when disconnected, the garage door opener works fine - it does not stop on the way up or way down! Is tehre a sensor or something inside the opener? we had a similar problem with ours and the plastic gears were worn to a point where the tension was ok going down but too worn to pull the door up . this is typical on craftsman. Pull the inspection cover and check for plastic shavings
You may have a stripped out gear but be careful because you may have a broken spring that caused the gear to strip out in the first place. First with the door in the closed position i would pull the disconnect cord from the opener. Then make sure that the door goes us and down manually without too much effort. If you can't open the door at all then the spring is probably broken. If you can lift the door but is seems to be binding then that's were you should start to address the problem. Yup, it was a spring. One had snapped, so we got both replaced and it works perfect now. Thank you for the help!I hope you got a good deal. Thanks everyone - it was the gear assemly - like a snow storm when I opened the back. Thanks ... read this post and found out I have a broken spring... now to find a good deal. Anyone know a good spring repair place in the NW Detroit suburbs? Loews has them for sale to replace yourself. All I did was unplug and replug the unit and it worked!!
One of your springs are broke. I had the same problem for sometime... well I say sometime, it was about an hour so I got on line and found that the sensors were out of line and had to realign them so they became green again... Door opens like new again.. I had the same issue where it opened about 2 inches and then stopped. At first I thought the Extention Springs were worn, so I bought new extension springs and pulleys, but still the same issue. Then I read the manual, and adjusted the "Opening Force" by 1/16 clockwise and that fixed the problem. I have a Genie screwdrive garage door opener. I still think replacing the extension springs and pulleys was a good investment as they were 13 years old to help reduce the load on the garage door opener. I adjusted the blue "up" screw about 1/32 to 1/16 of a turn up. My door operates perfectly now. I also lubricated every hinge point on the door as well as all of the rollers and applied some bearing grease to the gears inside the unit just for good measure.
I have the same problem but it only happens when the temperature outside is below freezing. does both sensors have to be green Mine are one is green and the other is yellow. I consider this normal, but I've heard on some units , both are green. I have a Genie Excelerator - about 10 years old. It stopped working about a week ago when it got really cold (below 0, I think) - would go up about a foot and stop. I had to hold down the button on the wall unit to get it to work and go up all the way - my remote wouldn't get it up beyond a foot. So, every day, I stopped in my driveway, walked through the snow to my front door and then came through the house to open it up! I was ready to call a repair company today. Decided to give it one last shot - I opened it up and checked the lift knob - was at max. I checked the sensors (one is green, one is red, and this is correct with my opener). I cleaned the sensors and insured nothing was in the way (they weren't blinking, and that means there's an issue, but I cleaned them anyway).
Checked all the wires - everything was good. I just had a new spring and new wheels put in a few months ago, so that wasn't it (door wouldn't even BUDGE when the spring was broken). It's always the easiest answer, huh??? I was about to give up but then, I UNPLUGGED it after I saw someone's post to do this, waited 10 seconds and plugged it back in...and yes, it's working! I'm kicking myself I didn't try this a week ago...wouldn't have thought of that unless I had read these posts, so thanks for the tips! I adjusted the up switch as you noted. I was having the same problem, I read this post and unplugged it and waited. Plugged it in after a minute, works perfectly. This post was chosen to be featured as a blog.How to fix a garage door that won't open The reason that screw drive openers do this when it gets cold is because the rail is general made of soft aluminum while the screw is usually made of steel. When the temperature drops the soft aluminum contracts onto the screw causing the motor to sense the presence of abnormal force.
Unplugging the machine resets it (genie), turning the force up is merely a band aid. You need to spray wd-40 into the rail from underneath where you can see the screw that spins, spray the entire length and press the button with the emergency release pulled to clear the old stiff grease out. Next you want to get some "Lubriplate", white lithium grease, or "low temp" grease, do not use any other type of grease WHITE ONLY. Apply a light line of white lithium grease to the screw from under the rail, front to back. Next re-engage the emergency release to allow the door to open and close, last press the button, the carriage will run the new grease into the rail. Wipe any excess off of the rail(but not the actual screw) to prevent it from dripping on your door or vehicle. As stated earlier merely resetting the opener may work but as soon as the cold returns you will be faced with the same issue, and turning up the open force also works at the expense of premature failure of your electric motor.
Fix it right, clear that old grease out, and apply new grease. Now pat yourself on the back, you just saved yourself a $95 service call, or better yet a $300 opener. Had the same problem, adjusted the lift weight and unplugged it, waited... working great, and how did we live before the internet? Wait that's another question Another Genie owner here who had the same problem. I managed to resolve the issue simply by UNPLUGGING as many others did. Thanks for the tip. Otherwise I must have called a repair guy. wait for several minutes... just like rebooting the computer to reset the system!!! I just save hundreds of dollars!!!Worked perfect for me after experience identical issues. Thank you , thank you. Tried the unplug trick and the door worked 1 time. Reset the up and down switches to the middle position and wiped down the top of the main chain bar and sprayed with silicone grease. Checked and cleaned both beams and they are green as they have always been.