I have a screen door that has a pneumatic brace that keeps the door open. It is currently stuck open and I'm trying to press the release mechanism, but I can't get it to release. Any ideas on how to get it to work? I just utilized Tester101's method of opening the door further and it worked perfectly. Just open the door as wide as it'll go and the locking gizmo disengages. I've had screen doors that were propped open with the brace and when people try to swing it shut without thinking, they end up bending the little metal brace itself, not allowing it to close. You can usually bend it back with a little shove but it probably won't shut as smoothly as before. If the little metal piece that keeps it open is stuck, then maybe get some pliers and wiggle it some to try and get it to slide back down so you can close the door. If the bracket that attaches the closing device to the door has a number of settings where you can put a screw, thenDetach the bracket that attaches to the door itself.
Then close the door a little bit and reattach the bracket so that there is a lot more slack to be able to open the door. Now you should be able to open the door wider and release the latching mechanismBrowse other questions tagged screens or ask your own question. Storm Door Repair Contractors Find Trusted Pros with HomeAdvisor ProFinder Just tell us about your needs and we'll quickly match you to the pre-screened, San Antonio Storm Door Repair Contractors you can trust to get the job done. Learn how we can help your business See recent jobs & leads Know any great Storm Door Repair Contractors in the San Antonio area? Let us know about them and you Refer A Pro today! More San Antonio Door Services More Texas Door Services More Texas Storm Door Repair Contractors Find Your Business Profile View All Unscreened Pros(Check all that apply) Woven woods in living area and in breakfast area. The following are recent projects that showcase our work and our ability to offer an assortment of styles and tastes.
Dining Room - Custom pleated silk drapery panels hung on a custom decorative iron rod. Recent Job Requests for Repair Storm Doors Contractors in San Antonio, Texas:Window & Door Parts When your window or door needs a new part, contact the experts at Window and Door Superstore. If it is still available, we’ll find it for you. We’ll be able to tell you quickly if it pays to repair or replace. < back to Specialty Products We carry a variety of entry door parts, including: - Replacement Bottom Sweeps - Jamb Compression and Magnetic Weather-stripping - Schlage Hardware Replacement and Parts - Kwikset Hardware Replacement and Parts - Replacement Hinges and Spring Hinges - Replacement Glass and Glass Frames - Change your clear glass to decorative glass or replace your creaked or yellowed glass frames We carry a variety of storm door parts. Please be sure to bring in your old parts to be matched or send us a picture of the part you're looking for so that we can help you find the match.
We will also need to know the Pella registration number and Larson registration number. Our storm door parts include: - Replacement Hardware (inside and outside) - Replacement Frames (Z-Bars) - Pella and Larson - Replacement Screw Covers – Pella and Larson - Replacement glass and screens - Rescreen with new material (in-store) We carry a variety of patio door parts. Please be sure to bring in your old parts to be matched or send us a picture of the parts. Our patio door parts include: - Replacement Hardware and Guts - Replacement Screens (materials and complete screens)Storm Doors are great features for homes and they provide a variety of different features from security to increased protection from wind and rain. The one feature that most storm doors do not come with is a chain that restricts how wide the door can open. This really is an important feature for most home owners because wind can pull a door out of your hand and cause it to hit something.
Also children, friends or even the mail man that visits may not be so careful and opening the door to its fullest extent may mean damage to the door or other features on your home. When installing our storm door I found that a chain was needed to restrict the door from hitting a outside light on our porch. The whole process takes under an hour depending on how long it takes you to get and put away your tools. The tools needed are pretty basic. Masking tape and a Pencil The first thing you want to do is read the directions for your specific chain set. Almost all of these chain sets install the same way but follow the manufacturer’s directions when they differ from the ones we provide. The Chain will be installed at two points by screws. The first point is the direct center of the door opening on the frame of the door. This side will retain the spring side of the door chain. On the actual door you will need to take a measurement that will be a few inches off-center on the top of the door frame to attach the retaining clip.
Before you begin place a few pieces of masking tape on the door frame and door to allow you to mark the locations on the tape rather then the painted surfaces. You will need to drill holes in the door frame and door top to receive screws for the retaining clips. Measure for the center of the door frame opening and mark it then using the clip that will retain the spring side of the chain place it where it will go and mark the holes for drilling. Before you drill the holes in the door frame you want to use your center punch to mark the location. This will give you a starting dimple in the wood so your drill bit won’t slide when you begin drilling. Install the clip and screws for the door frame side of the chain but do not install the chain yet. You are simply starting the screws in the wood. Once you have the door frame clip installed you can install the clip on the door. Take your measurements from the manufacturer’s directions and place a center mark on the door.
Once you have the clip location set you can repeat the process above and use the center punch to mark the location of the screw holes for the clip. Before you begin drilling holes on the door you must mark your drill bit for the depth of the door. First double check that the screws you are using won’t go all the way through the door by placing them up against the open door edge. The holes that you will drill must not go through the door but they must be deep enough that when you screw in the clip there won’t be dents from the compressed wood in the door. Place your drill bit against the edge of the door and mark it about 3/4 of the way into the door. You want to pay close attention to the molding around the edge of the door because it will make the door seem about a 1/4″ thicker then it actually is. Mark the drill bit with masking tape. Use a few loops around the bit so it will not move while you are drilling. You can now drill the holes in the door safely.
Once the holes are drilled you want to attach the clip and make sure the screws tighten it down securely before you install the chain. Install the chain on the door frame first. Once the fixed side of the chain is secure you can open the door and hold the chain in place to get the measurement for the adjustable side that will mount on the door. Make sure that you give plenty of distance between the door and any obstruction. When the door chain extends to its widest position the spring on the chain will allow it to extend a few more inches so take that into account and install the adjustable side on the clip a few inches shorter then the full maximum amount the door will open. Secure the clip and chain then check your work by opening the door and pulling on it lightly to expand the chain spring to its maximum distance. If the door is hitting or coming close to an object reposition the chain and test again. This is a pretty easy project but you must be careful about the spring loaded chain measurement.