Replacement Parts: Pools or Spas | If my airbed has a leak, how can I find it and patch it? First, make sure that the airbed is leaking. Stretching is a natural characteristic of new vinyl and the first few times you use the mattress, some stretching will occur suggesting that the mattress is losing air. It is simply stretching under your body weight and this is normal for the first few uses. To check the mattress for leaks, first make sure the valves are secure, replace it if necessary. You can also put liquid soap and water in a squirt bottle and spray on seams. If there is a leak it will bubble. (Laundry detergent and dishwasher detergent will not work; they do not have the "bubbling" effect) After you find the leak, clean and dry the leaking area, remove the flocking with fine sand paper or an emery board, then apply the repair patch that comes with your airbed. Alternatively, you may purchase an Intex repair kit (#59632) for additional patches. Does the INTEX airbed come with a warranty?
How can I differentiate the valves? A Built-in Pump is a pump that is mounted inside of the airbed with the panel portion showing. A 3-in-1 (part# 10650) Valve has two "clips" on either side of the Valve Cap that allows for easy removal. A 2-in-1 (part #10651) Valve does not have "clips" and instead consists simply of a screw-on cap, and a plug that fits on top, and in the center of the cap itself. The Exhaust Valve Cap (part# 10043) and Plug (part# 10044) consists of a rubber stopper plug that is inserted first, while the screw-on cap is placed on top of the plug. The Double-Valve is a vinyl valve stem that is attached to the mattress and is reminiscent of a beach ball valve. What pump should I use with my airbed? What type of valve does my airbed have? Since my airbed has flocking, how can I use the repair patch - it won't adhere to the flocking? The repair patch is designed for vinyl surfaces only. However, fine sandpaper, or an emery board can be used to gently rub away the flocking.
When that is complete, clean the area with nail polish removal solution so the repair patch will adhere to the bed. How to repair the airbed What is the approximate weight capacity of INTEX airbeds? Can I use normal sheets for my INTEX airbed? How can I inflate an airbed with 2-in-1 or 3-in-1 valve? Please refer to the Manual comes with your airbed or visit the following link for the video instruction. What is your suggestion on pump maintenance? How are the airbeds constructed? Can I use an airbed on my existing bedspring? Why won't my Quick-Fill Rechargeable Pump work? I turn it on and nothing happens. I misplaced the transformer to my Quick-Fill Pump. Which transformer do I purchase to replace it? Will the Quick-Fill Rechargeable Pump inflate my airbed? Can I wash my airbed? Can I use other brand's pump for inflating the airbeds? Why doesn't the product measure out to the size stated on the box? INTEX airbeds state the approximate inflated size;
Make sure the airbed is inflated before it is measured. Make sure to incorporate the bulge on whichever side you are measuring. All sizes are approximate which will be affected by the pressure, temperature and etc. You may get a measurement different than what is stated on the packaging due to the above.How to measure the size of airbed Can I use other brand's pump for inflating the airbeds?Edit ArticleHow to Inflate an Air Mattress Three Methods:Inflating with a PumpInflating Without a PumpDeflating the MattressCommunity Q&A When you're camping, having a friend over to spend the night, or just looking for a convenient place to crash, an air mattress can be your best friend. These handy mattresses can make for comfortable sleeping and usually compress to a fraction of their full size, making them highly portable and convenient. Whether you're working with a mattress-compatible pump or simply using the tools you have handy, inflating an air mattress is a simple matter of pushing air into the mattress (and keeping it from coming back out!)
Open the valve cover. Most air mattresses have either a one-way air valve (which allows air to easily enter the mattress but not leave it) or a simple hole somewhere on the side of the mattress. Your first step should be to locate this and remove the protective cap — you can't put any air inside the mattress without an opening to do so. Note that some modern mattresses have pumps built into the side of the mattress. In this case, simply flip the "on" switch, and, provided the pump is receiving power either from an outlet or batteries, it will start to inflate the mattress.Whether you're using an electric pump or a manual one, your next step is the same: insert the pump's nozzle into the hole or valve opening. The pump should make a tight seal with the material around the valve. If it doesn't, there's a chance that air may escape around the pump, making it harder to fully inflate the mattress. If you can't get a tight seal around the pump (for instance, if you're using a pump that wasn't made for the mattress), you may want to try laying duct tape around the pump to keep it seated in the valve, though this can be ineffective if the pump is very loose.
Another option is to melt plastic around the pump to make it thicker and give it a tighter seal, though this can present challenges for novice repair experts. If using an automatic pump, turn it on. Most modern air mattresses come pre-packaged with an electric air pump. If this is what you're using, make sure it's plugged in or has battery power, then turn it on! The mattress should immediately begin to inflate. Note that electric pumps are usually quite loud, so you may want to be careful about running them around where others are sleeping. If using a manual pump, start pumping. If you're working with an older air mattress or you lost your electric pump and had to buy a replacement, you may only have a manual pump at your disposal. Though these aren't as quick and effortless as electric pumps, they're usually quite effective in their own right. The two main types of manual pumps used for inflating air mattresses are: Hand pumps: Usually large, standing pumps operated with an "up-and-down" motion.
However, smaller hand-operated bicycle-style pumps are occasionally used. Foot pumps: Usually take the form of a foot pedal attached to a hose and nozzle; stepping on the pedal repeatedly forces air into the mattress. Screw the latch back on. Once the mattress is filled to the point that it is fully inflated and firm to the touch, remove the pump, then screw the valve or hole cap back on to trap the air inside. You're now ready to sleep! Grab some sheets, blankets, and pillows. Note that air mattresses with one-way valves will automatically trap air inside. It's still a good idea to screw the cap back on for these mattresses to provide another layer of protection against deflation. Mattresses with simple air holes (and no valves), on the other hand, will immediately begin to deflate as soon as the pump is removed, so you'll need to screw the cap back on quickly! Use a hair dryer if there is no pump available. If you don't have any pump to inflate your mattress with, don't worry — it's possible to use common household items to do the trick.
For instance, you may want to try using an electric hair dryer. Simply turn the hair dryer on and hold it against the open valve hole to begin filling the mattress. Because the hair dryer won't perfectly fit your mattress's air hole, the inflation process will usually be slower than when using a pump. Be sure to use cool air, not hot air, if you have a choice. Most air mattresses are made from plastic or vinyl, which can sometimes melt or deform if exposed to high heat. Use a vacuum cleaner or shop vac. Any sort of machine that can be made to blow air can conceivably be used to inflate an air mattress. For example, many shop vacuums have a "blow" function in addition to their ordinary "suck" function. Other tools, like snow blowers or leaf blowers, are specifically made for blowing. With a tools like these, all you need to do is hold the nozzle or blower up to the air hole or valve and blow to inflate the mattress. It's even possible to convert some ordinary home vacuum cleaners to blow air instead of sucking it up.
To do this, remove the bag and connect a long, narrow cleaning nozzle to the hole that the bag was originally attached to — air will shoot out of this nozzle and can be used to inflate your mattress. Use a bike or tire pump. Use a garbage bag. Most people don't know that it's possible to inflate an air mattress with nothing more than a standard-size plastic garbage bag. To do this, first open the bag and swing it up and down to catch plenty of air. Gather up the open end of the bag to trap the air inside. Bring the bag up to your mattress's air hole and hold the open end of the bag around it. Squeeze the bag to force the air out and into the mattress (it's often easiest to do this by slowly laying on the bag). If you have a choice, use heavy-duty trash bags for this method. Weaker bags are vulnerable to popping under your weight Inflate it with your breath if all else fails. If you can't find any of the objects above to help you inflate your mattress, take a deep breath and try the old-fashioned way.
Use soap or sanitizer to ensure the mattress's air hole is clean, then simply put your mouth against it and exhale. Repeat until the mattress is full and firm — using your mouth, this can take some time. If your air mattress doesn't have a one-way valve, you'll need to keep your mouth pressed into the air hole and close your throat to keep air from escaping between breaths. Breathe through your nose to fill your lungs rather than using your mouth. Unscrew the valve cover. When you're done sleeping on your air mattress and want to stow it for storage, unscrew the air hole cover. If your mattress has a simple air hole, it will immediately begin to deflate. However, more complicated models may require slightly more action on your part. If your mattress doesn't immediately start deflating, try one of the following tips:[3] Look for an air-release switch to flip Turn an air-release mechanism on the valve to let air escape Unscrew the valve itself from its housing