Manufacturer Model # GD-00Z-1 Power - The control unit plugs into the same outlet as your garage door opener. The included tilt sensor uses a CR2032 watch style battery. Type of Wireless Communication - Z-Wave (Iris Smart Hub Required) Compatible Garage Door Openers: According to the manufacturer this device works with most openers. the manufacturer has identified the following openers as being incompatible. In addition, if the garage door opener is operable through the Chamberlain MyQ Garage system, it will not operate with the Iris Garage Door Opener. These systems are mutually exclusive. Please refer to this link for Chamberlain's list of MyQ-compatible devices. Note: This device is compatible with Iris 1st Generation and Next Generation Hubs Pairing a New Device Step 1: Before you begin, make sure your door opener has exposed terminals. Step 2: Follow the installation instructions to attach the tilt sensor mounting plate to the top panel of your garage door.
Step 3: Remove the battery tab from the tilt sensor and attach it to the plate, ensuring both arrows are pointing up. Step 4: Open the Iris app and go to the “Add” section, tap “Device,” and browse or search for the device. This will put the hub in pairing mode, indicated by a blinking green light. Step 5: Plug the garage door controller into an electrical outlet close to where it will be installed. Do not connect it to your garage door motor yet. Step 6: Press the Link button once. Step 7: When the hub triple beeps, your device has been paired. Step 8: Mount the garage door opener and connect it to your garage door motor as described in the installation instructions. Step 9: Finally, configure the tilt sensor orientation by manually opening and closing the garage door before controlling it through Iris. You should perform a reset if the controller was force removed from the app or you are having pairing, connectivity, and/or response issues.
Step 1: In the app, tap on the Left-Hand Navigation Menu (≡), then tap on Devices. Step 2: In the device list, scroll down to the bottom of the list and tap on Z-Wave Tools. Then tap on Remove Z-Wave Devices. Remain on this screen until step 3 is complete. Step 3: Go to the garage door controller, and press the pairing button once. The garage door controller should give a short beep immediately followed by a long beep. If the hub can be heard from the controller's location, it will beep twice as well to confirm the reset. The Iris app will list which device has been reset. Step 4: If you did not get confirmation in the app, press the pairing button on the garage door controller five times in a row, once per second. The garage door controller should give a short beep followed by a long beep several seconds later. If you received confirmation in the app, proceed to the next step. Step 5: To re-pair the device, put the hub in pairing mode by tapping the plus sign on the dashboard, then Device.
Step 6: Press the pairing button on the garage door controller once more. The garage door controller will triple-beep when pairing is complete. If the hub is in hearing range, you should hear it triple-beep as well. Garage Door Controller Installation ManualGARAGE DOOR REPAIR CENTEROn The Job When You Need It Most...Service Repair Line @ 415-883-3992 call now At GS Overhead Systems we have been Repairing and Servicing garage doors and garage door openers since 1995. After 20 years in the business, we can solve just about any problem you may encounter with your garage door operating system. Having a working garage door is very important, and we understand that here at GS. Your vehicle is one of the most valuable items that you own. You need to protect it, and have it accessible for travel or emergency situations. Our technicians are available - (7 days a week) to assist and advise. We have an excellent satisfaction rate and value our customers highly. Our service is fast, efficient and very cost effective to you.
Our goal is to get your garage door system set up and running asap. Service trucks are in your area... Emergency Service & RepairGarage Door Spring ReplacementDoor Balancing and AdjustmentGarage Doors Off TrackCables and Torsion SystemsOne Piece Garage DoorsPreventive Maintenance & Door ServiceOverhead Garage DoorsGarage Door InstallationSectional Garage DoorSafety Sensor/Infra Red Eyes Garage Door Opener RepairGenie Garage DoorsLiftMaster Garage Door OpenersChamberlain Garage DoorCraftsman Door Opener RepairGarage Door PricesUniversal Garage Door OpenerGarage Door Repair ServiceAutomatic Door Opener PricesWeather Stripping & Bottom SealReviews, Brochures & much more... Check out the YouTube channel for G S Overhead Systems. You can view videos on how to program remotes & keyless entry devices. Demonstrations of garage door installation, repairs and more. Stay tuned for more vids.About Your Garage System1. A garage door spring will last about 10 yrs. with normal daily use.2.
You can special order a higher cycle spring, that will last 20-30 yrs.3. The average life of a garage door opener is about 15-20 yrs.4. The battery in your battery back up unit will last about 7 yrs./1 year warranty.5. You can quiet your Genie screw drive unit with a special low temp. grease.6. There is a posi-lock system in most chain drive openers, that makes it almost impossible to break in with a crowbar.7. Use a silicone spray lube for your squeaky garage door hinges. Call Our Office & Schedule an Appointment @415-883-3992 What we can do for youGarage door repair: Replace your broken garage door torsion spring with a new high quality spring. Full warranty on parts and a low price guarantee. If your garage door is off track. We can reset your door adjust the spring and have you going in no time. Cable came off the drum. Are your garage door panels damaged. We can special order new sections that are available. Overhead garage door service and maintenance. Wood garage doors repaired.