Learn more about IHS GoldfireUsing a hammer and a flat screwdriver, remove the hinge pins and lift out the old door. Unscrew the hinges from the door. Next, unscrew the hinge leaves and remove them from the jamb; keep the old hinge sets together, including all screws, hinge leaves and hinge pins. Using a utility knife, score the caulking between the molding and the brick to break the seal. Use a pry bar and hammer to carefully remove the molding. Pry away the door jamb, framing and threshold. Finally, scrape away old caulking. To calculate the exact dimensions of the door opening, measure the width between the side jambs, the head jamb to the seal under the old threshold, and the thickness of the wall. The rough opening should be at least one inch wider and taller than the outside frame dimensions of the pre-hung door to be installed. Be sure to measure carefully. With the shipping brackets still attached, carefully set the door in place, centering it in the opening.
If necessary, add shims under the lower side jamb until the entire unit is plumb and level. With a carpenter's pencil, mark a line at the top of the door on the brick lintel, then carefully remove the door. Use the level to mark plumb lines on both sides of the opening. These lines will serve as guides for the molding of the new door. Remove any remaining pieces of paneling around the door to ensure a clean opening. For a very rough opening -- one that has concrete or cinderblock as the jamb -- pressure-treated lumber may be necessary to frame out the door. For this, take the measurements for the side jamb and cut the board to length. After checking for plumb, install the board using cut nails designed for fastening to masonry. This board will act as additional framing for the new door. Begin installation by first running a thick bead of latex caulk along the subseal at the bottom of the old door opening. Then lift the new pre-hung door into the center of the rough opening, positioning the bottom seal first, then tilting the door into place.
Check for plumb and shim the frame as necessary. Secure the door with cement screws at each shim location. For wood frames, use casing nails. Trim off excess shims using a utility knife and pry bar. Remove the shipping brace and test the operation of the door. Finally, attach the long-anchor screws (provided with the door) through the hinges and into the door framing. To seal the exterior of the door, run a bead of paintable latex caulk around the entire door. Fill holes left by the screws with wood filler. Inside, insert fiberglass insulation into the voids between the door frame and opening. Attach trim to the door with fourpenny finishing nails. Once the caulk and wood filler have dried, you can apply paint to the door and wood trim to match the color of your home. Finally, attach the door handle and deadbolt to the new door.“Meets Uniform Load Structural Requirements for all U.S. coastal building zones.” • Prehung 4-way universal swing • 1-3/4” thick door panel
• Pressure injected with 2.2 pounds of polyurethane foam per cubic foot • R-12 insulation value • Extruded aluminum reblocks for lock • White and brown panels and jambs • Rolled edge door panel • Prepainted with two coats of polyester paint for a durable and long lasting finish • Door is mounted to the frame by three 12-gauge steel, 4 1/2 ” x 4” fixed pin hinges • Hinges treated with rust inhibitor, painted and lacquer dipped for exterior installation • 2’4” to 4’0” widths and double doors standard • Prehung door individually boxed • Designed for steel, masonry and wood construction • All lites are aluminum framed and foamed in place • 24 gauge smooth steel skin • Woven polypropylene pile weatherstripping • Panel available with crossbuck stamped design • 3700 panel in aluminum nailing fin/J-channel jamb Options to Fit Your NeedsSizes from 2’0″ to 4’0″ wide and 6’8 high available
Single-glazed and insulated tempered door litesGrids available on insulated 9-Lite and Fullview LitesCrossbuck pattern check for availability • Custom Colorization Available Click here to download Vent Lite SpecsEntry doors 101: Selecting the right door for your home As an industry leader, Pella proudly produces quality windows and doors to meet customer needs,. For a deeper look at the dynamics of doors, here’s a quick download of the features found at Pella. Features of wood entry doors Pella entry doors are available in four stylish collections: Traditional, Craftsman, Classic and Old World European Available in Rustic Walnut, Mahogany, Demesne Cherry and American White Oak A variety of decorative glass options available to provide a distinctive look True divided light with beveled glass options provide a classic look Pella wood entry doors are prehung for maximum ease in installation Available with choice of sill finishes, including Aluminum Mill, Anodized Brass and Anodized Bronze finishes, to match varied décor and finish preferences in today’s homes and businesses
Standard ball bearing door hinge options include black, bright brass, oil-rubbed bronze and satin chrome finishes, to match varied finish preferences in today’s home and commercial settings Feature adjustable thresholds, foam compression weather-stripping, bottom sweep, and ball-bearing hinges Available with single or double-bore hardware prep, or with a factory-installed multi-point lock for added security and performance Where available, Pella strives to use wood from certified suppliers, supporting responsible forestry management practices For best results and maximum life, wood requires regular maintenance to maintain its natural beauty Features of fiberglass and premium steel doors Factory-assembled and pre-hung for quality assurance and easy installation Pella entry doors with an aluminum-clad frame come standard with the exclusive Pella AdvantagePlus™ Protection System* that combines three key components: Pella entry doors are protected by an aluminum-clad exterior frame that is virtually maintenance free.
It doesn’t need painting and it won’t flake, crack or peel. The AdvantagePlus system features a tough snap-in aluminum exterior brick mould trim that extends the maintenance-free benefits to the area around the door. AdvantagePlus features a patented rot-resistant design. For added convenience, opt for factory prefinishing For added style, choose from a variety of glass options including Pella’s exclusive decorative glass collections and Low-E with argon-insulating glass** EnduraClad® aluminum clad exterior frame available in 10 colors: White, Brown, Tan, Hartford Green, Poplar White, Putty, Brick Red, Black, Morning Sky Gray and Hemlock; primed wood frame also available Aluminum-clad exterior one-piece fin/frame design allows for easy installation and reliable performance Fiberglass entry doors are able to withstand dents and dings Hinges and hardware available in a variety of finishes, including standard brass-tone zinc dichromate, polished brass, antique brass, antique nickel, polished chrome satin nickel and stainless steel (outswing doors only) to match varied finish preferences in today’s home and commercial settings
Complete offering includes matching sidelights and transoms Flexible compression foam weather-stripping system helps prevent air and water infiltration Energy-efficient core in the door panel provides outstanding comfort and stability Threshold has adjustment capabilities to counteract house settling and help ensure consistent performance and operation throughout the life of the door Transoms and other Pella products can be easily attached with mullion kits Glazing frames are composed of an engineered material for lasting good looks and durability Wood-grain detail with self-aligning screw covers Six in-swing wall depths, one out-swing wall depth and one low-profile wall depth available Entry door glass options Each decorative glass collection features a unique combination of glass style, texture and caming (the decorative metal used to assemble glass pieces into a design) Variety of decorative glass options to let the sun shine through and to add architectural elegance to any home style
Exclusive decorative glass designs are sandwiched inside a sealed insulating glass unit to deliver elegance, and energy efficiency Textured glass permits light to pass through, yet also allows privacy In clear glass, Pella offers a wide selection of entry doors, sidelights and transoms made with standard insulating glass or Low-E with argon-insulating glass** For a classic style, choose from a variety of permanent or removable grille options and standard grille patterns for the traditional look of divided light. Custom patterns are also available. From light to dark — from black to copper to satin nickel options — Pella offers a variety of caming materials to add decorative detail to doors. A transom is a fixed window aove an entry door for extra light and view. Transoms with matching deocrative glass or grilles are available on Pella entry doors. A sidelight is a fixed window placed next to an entry door for extra light and view. Matching sidelights with decorative glass or grilles are availble on Pella entry doors.