Chair Saver KitOffice chairs don't last forever. The cylinder eventually fails, leaving you with a sinking office chair when you sit down. There used to be only two options for a sinking chair. Buy a new office chair or replace the adjustable cylinder - neither very cost effective. Now a new solution exists. A Chair Saver kit will fix your sinking office chair, saving you time and money. Just $19.95 with a 30 day satisfaction guarantee and 5 year warranty. You have nothing to lose but that sinking feeling!Chair Saver Kit updated their profile picture.See allChair Saver KitYou can buy the Chair Saver Kit directly from us on Facebook!! Just click the Products link on the left hand side to make a purchase. Or check out our new web site by clicking the Shop Now button if your on your phone for more information and to buy. Our shipping never has a markup and each kit comes with a 30 day satisfaction guarantee and 5 year warranty. You have nothing to lose, but that sinking feeling!Chair Saver Kit added 2 new photos from 6 January 2013 to the album Product Insert.Chair Saver Kit added 2 new photos from 6 January 2013 to the album Installation.How To Install The Chair Saver Kit
New (2) from $8.99 & FREE Shipping on orders over $35. Sold by chairpartsonline and Fulfilled by Amazon. Replacement Hardware Repair Kit for Office Chair Gas Lift Cylinder - S4451-K FREE Shipping on orders over . DetailsRolland Office Chair Gas Lift Cylinder – Universal Size Fit All - Heavy Duty - Black FREE Shipping on orders over . Useful for replacing or repairing worn out or missing attachment hardware on an office chair gas lift cylinder. Attaches the gas lift piston cylinder to the larger black or chrome support column that fits into the 5 leg chair base. Instructions for correct assembly included ** It is critical that this hardware set is installed in the correct order for proper & safe usage. Note: Gas lift piston in picture is for visual purposes only and is not included. Only the hardware kit is included. 4 x 7 inches 4.3 out of 5 stars #1,544 in Home and Garden (See top 100) #151 in Office Products > Office Furniture & Accessories > Furniture Accessories
9.6 ounces (View shipping rates and policies) 5 star71%4 star14%3 star7%2 star3%1 star5%See all verified purchase reviewsTop Customer ReviewsUsed for Aeron Chair; Silver Washer is too Thick.Works on Aeron ChairsThe problem: center rod was pushed through the bottom of the center post. The Solution: this Kit!Worked well to fix a Herman Miller Aeron ChairThis got worse over timeSaved me $150!Repaired by $600 Aeron chair I was about to toss. See and discover other items: aeron chair partsUser ReviewedHow to Fix a Sinking Desk Chair Two Methods:Using a Hose ClampUsing PVC PipeCommunity Q&A Office chairs use a pneumatic cylinder that controls the height of the chair through pressurized air. The cylinder on most chairs fails within a few years, typically because the seals are too damaged to maintain pressure. You can buy a replacement cylinder to restore full function to your chair, but this is nearly as expensive as buying a replacement. Try these simple DIY methods instead to fix your chair at one convenient height.
Slide the plastic skirt off the cylinder. Most office chairs have a plastic tube over the extendable cylinder. Slide this all the way down or up, until you can see the metal cylinder underneath. Set the chair to the preferred height. You will not be able to adjust the height after this repair, so make sure you have it right. The seat of the chair should be level with your knees when you are standing. If the chair won't stay up even when no one is on it, lay it on its side. If the plastic skirt covers the cylinder at this height, you will need to remove the skirt first. To do this, turn the chair upside down, push the retaining clip at the base with a screwdriver, and pull off the wheels, then the skirt. Slide the wheels back on. Wrap a hose clamp around the cylinder. Get a ¾" (2 cm) hose clamp (Jubilee Clip) from a hardware store.[2] Loosen the screw on the hose clamp (Jubilee Clip) and pull out the belt end. Wrap the clamp around the metal cylinder, but do not tighten it yet.
Improve the grip of the clamp (recommended). The clamp will need to be very tight to hold the chair up. Give the clamp a better surface to grip by wrapping a strip of rubber or a couple layers of duct tape around the cylinder.[3] Do this at the highest visible point on the cylinder, Alternatively, scuff up this area of the cylinder with sandpaper. If the cylinder looks dirty or greasy, clean this off first. Tighten the clamp as far as possible.The chair should now be unable to slide down past the clamp. The built-in height adjustment will still not work properly. If the chair is at the wrong height, move the clamp higher or lower on the cylinder. If the clamp slides off, fasten it over a strip of rubber to improve the grip, or try the PVC pipe method below. Measure your chair's cylinder. Pull down the plastic skirt cover the extendable, metal cylinder. Estimate the diameter of the cylinder by holding a ruler across it horizontally. Also measure the length of the cylinder when the chair is at the perfect height.
You shouldn't need an exact measurement, but you can calculating the diameter from the circumference if you prefer to be precise. Buy a length of PVC pipe. This pipe will fit over the pneumatic cylinder of the chair. It should be about the same size as the cylinder diameter, or slightly larger. Pipe 1.5 inches (3.8 cm) in diameter works well for most models.[5] Buy enough straight pipe to extend from the wheel base of your chair to the seat, when the chair is at the preferred height. The pipe does not have to be in one piece. It may be easier to work with in smaller pieces, although you can easily cut it yourself at home. One user reports using a tall stack of plastic shower rings instead of PVC pipe. These are even cheaper and easier to install, but they may not be sturdy enough to support your weight. Try at your own risk. Saw through the PVC pipe lengthwise. Secure the pipe in a vise. Use a hacksaw or back saw to cut through the pipe from tip to tip, but only on one side.
The end result should be a pipe with a slit in it, not two half-pipes. Wearing a mask or respirator is recommended while cutting PVC to avoid inhaling irritating particles. If you do not have a vise or cutting tools, just leave the pipe intact and remove the chair's wheels so you can slide on the pipe. In most cases, you can remove the wheel base by pressing a retaining clip on the underside with a screwdriver. Snap the pipe onto the chair cylinder. Pull the chair's plastic skirt up or down to reveal the metal cylinder. Push the slit side of the PVC pipe against the cylinder to snap it around the cylinder. It should now hold the chair in place, preventing it from sliding down. If you're having trouble snapping the pipe on, saw it into shorter pieces and try again. Add more pipe to adjust the height of the chair. You can also buy a replacement pneumatic cylinder for your chair. However, the cylinder often costs nearly as much as a new chair, and can be tedious and difficult to install.