2-Door Set Bi-Fold Door Repair Kit Set your store to see localavailabilityBi-Fold Door Hardware Set Bi-Fold Door Bottom Pivot and BracketSatin Nickel Plated Bi-Fold Door KnobBi-Fold Door Pivot Set Bi-Fold Door Bottom Pivot Bracket Bi-Fold Door Top Pivot and Guide Wheel Bi-Fold and Pocket Door Top Roller Assembly Bi-Fold Door Pivot and Guide Set Bi-Fold Door Top Track Pivot BracketBi-Fold Door Top Pivot Satin Nickel Bi-Fold Door Hinge, Pack of 2 Mill Bi-Fold Door Pull KnobNylon Top Pivot and Guides for Bi-Fold Doors (2-Pack)Nylon Bi-Fold Pivot and GuideBi-Fold Door Top Pivots (2-Pack)Bi-Fold Door Set (1-Pack) Gold Zinc-Plated Bi-Fold Door HingeBi-Fold Door Nylon Top Pivots (2-Pack) Set your store to see localavailability200FD Bi-Fold Door Hardware 125lbs [57kg] Max Panel Weight Each 48" [1219mm] Max Panel Width Each 108" [2743mm] Max Panel Height 1-1/8" [29mm] to 1-3/4" [44mm] Panel Thickness
Top Mount Hanger Type Commercial Grade Top Hung Bi-Fold Door Hardware 200FS Side Mounted Bi-Fold Door Hardware 1-3/8" [35mm], 1-3/4" [35mm], 2-1/4" [57mm] Panel Thickness Side Mount Hanger Type 100FD Bi-Fold Door Hardware 75lbs [34kg] Max Panel Weight Each 24" [610mm] Max Panel Width Each 1" [25mm] to 1-3/4" [44mm] Panel Thickness 100FS Side Mounted Bi-Fold Door Hardware 1-1/8" [29mm], 1-3/8" [35mm], 1-3/4" [44mm] Panel Thickness 111FD Bi-Fold Door Hardware 50lbs [23kg] Max Panel Weight Each 3/4" [19mm] to 1-3/4" [44mm] Panel Thickness 1700 Bi-Fold Door Hardware 40lbs [18kg] Max Panel Weight Each 96" [2438mm] Max Panel Height Residential Grade Top Hung Bi-Fold Door Hardware 1700FS Side Mounted Bi-Fold Door Hardware 3/4" [19mm], 1-1/8" [29mm], 1-3/8" [35mm] Panel Thickness 1825 "Tap-In" Bi-Fold Door Hardware 35lbs [16kg] Max Panel Weight Each 1-1/8" [29mm] to 1-3/8" [35mm] Panel Thickness
Tap In Pivot/Guide Type Residential Grade Bi-Fold Door Hardware 1601 "Full Access" Bi-Fold Door Hardware 30lbs [14kg] Max Panel Weight Each* Residential Grade Full Access Bi-fold Hardware *Heavier Panels Possible With Optional HingesCompany Contact Project List You are viewing the website. To change locations, choose a location below Home Designs by Stanley Rope & Chain Accessories Screen & Storm Door Hardware Track, Hangers & Sliding Doors For folding wardrobe and cupboard doors weighing up to 14kg each Ideal for cupboard and wardrobe doors For timber, timber framed or composite doors Additional fitting kit for 2 doors available (See optional extras, order code BF2) Supports a maximum door weight of 14kg each The Bifold range of folding door hardware offers a stable, silent and smooth-opening folding system for cupboard and wardrobe doors that can complement any room. Designed for timber, timber framed or composite doors the Bifold system can support a maximum door weight of 14kg and door thickness of between 18-35mm.
A range of kits are available up to a maximum opening of 2134mm. Kits contain an aluminium top track with fittings and spring loaded guides which complete this low maintenance system. View the installation video at the bottom of the page. Choose Your Product : Choose an optionB10/2 - 1067mm Track, 2 DoorB15/4 - 1524mm Track, 4 DoorB20/4 - 2134mm Track, 4 DoorClear Alternatively, order direct on: 0191 377 7345 or Contact Us Product CodeNumber of DoorsDoor MaterialMaximum Door WeightTrack LengthMaximum Door SizeB10/22Wood14kg1067mm2400 x 530 x 35mmB15/44 (2+2)Wood14kg1524mm2400 x 530 x 35mmB20/44 (2+2)Wood14kg2134mm2400 x 530 x 35mm2 Please choose an option from the product drop down menu above to see the relevant optional extras. Bifold 2 Door Fittings Kit 2 door fittings kit to be used where additional doors are required for a Bifold system. Includes hinges, top and bottom pivot and sliding guide. 311 - Top Pivot Socket 312 - Bottom Pivot Socket
313 - Top Pivot 312 - Bottom Pivot Bifold doors are much like any doors, only connected into pairs with hinges and hung on a track. What makes them look good and work well are a solid, heavy construction and sturdy and carefully adjusted hardware. The heft of the doors is what keeps them from shuddering when you open them. So it's best to look for solid–core or solid–wood doors, which will feel more substantial than hollow–core doors. (Solid doors are also easier to trim if any part of your door opening is out of square.) Then, in order to handle the weight of these heavier doors, you'll need a track that includes a wheeled mechanism, which allows the doors to glide smoothly rather than shimmy along the track. The most difficult—and sometimes most frustrating—part of the installation is attaching and adjusting all the hardware. The track, the pivots, the hinges all have to be assembled just so, and it's worth taking the time to double–check every measurement and position to be sure each piece is in the right place and facing the right way.
Finish or paint the doors before starting. Label the doors to show the order they'll be installed and which sides face out. Take a jamb side door and mark its inner edge 11 inches from the bottom, 7 inches from the top, and centered between the two. Place the door on edge with the marks facing up. Take the lower half of a hinge and align its bottom with the bottom mark, its knuckles facing back and flush to the edge. Use a self?centering bit to drill pilot holes through the hinge holes. Screw on the hinge plate. Attach the top and middle hinges, on their marks. Place the leading (inner) door on edge, facing back-to-back with the first door. Align the doors evenly against a square, then put the hinges together. Screw the hinge plates to the leading door. Repeat on the second pair of doors. Attach the track hardware Fasten the pivot plates (the pins that fit into the track and the floor bracket), and the locking arms (the hooks that slide along the track) to the top and bottom of each set of doors.
The pivot plates go on the tops and bottoms of the jamb–side doors, and the locking arm on the tops of the leading doors. Each kit requires its hardware to be uniquely positioned, so check the diagrams that come with yours for exact measurements and placements. These will tell you, for example, not only how far a pivot plate should be from the door edges around it but also where its pin should be in relation to the door's edges. Adhering to all the given dimensions ensures that no piece goes on backward. Use a hacksaw to cut the track to length to fit the closet opening. Slide the hanging hardware into the track—the small stops in the center, then around them the track hangers with wheels, and finally the pivot socket on the outside. Attach the track to the door header with the screws provided. Position the track 1 inch in from the front edge of the header. This will give you enough room to hide the track with trim without limiting the door action. Tip:Don't tighten the hardware onto the track.
It will be easier to hang the doors later if the pieces are loose. Position the floor bracket Use the measurements supplied by the manufacturer to position the floor bracket next to the door jamb. Hang a plumb bob from the center of the track above the floor bracket to align the pin hole in the bracket front to back. This will ensure that the doors are plumb when installed. Outline the bracket in pencil to mark its exact location. Screw the bracket in place, then remove the screws and set the bracket and screws aside. Bring the doors to the track and lift the jamb side to hook the pin of the top pivot plate into the pivot socket. Make sure the pin is all the way in, then push the lever on the side of the socket to lock it in place. Slot the pin from the track hanger into the locking arm on the leading door. Twist the arm to lock it into place. With the doors closed, swing them forward enough to catch the floor bracket in the bottom pivot pin. Attach the floor bracket
Swing the doors back into place and align the floor bracket with the pencil marks. Use a flexible bit extender to screw down the bracket. Hang the other set of doors. Close both sets and adjust them along the track to even up the reveal around them. Then, using the wrench provided with the hardware, tighten the pivot sockets on the ends of the track and the small stops in the center. Tip: Ask a helper to give you a hand in lifting and holding the doors, which can be unwieldy. Attach the door aligner From inside the closet and with the doors closed, mount the door aligners between the two leading doors, 6 inches up from the floor. The aligners catch when the doors are closed, keeping the door faces flush with each other. From outside the closet, check the alignment. Adjust the track hardware as necessary to keep the reveal around the doors even. Install the door pulls For flat doors, measure 36 inches from the floor on each leading door. Then mark the center, side-to-side, at that height.