Home HOLLOW CORE INTERIOR 1980 x 410/460/510/560/610/660/710/760/810/860/960 x 35 (Available with primed hardboard skins made to order.) 2400 x 410/460/510/560/610/660/710/760/810/860/910 x 35 (Available with hardboard skins made to order.) NOTE: Overheight doors please refer to the guarantee on the back cover. Hollow Core Sliced Pacifi c Maple doors are made to order and are supplied unclashed. Construction similar to Primecoat doors. 1980 X 410/460/510/560/610/660/710/760/810/860/910/960 x 35Duramax Fibreglass Doors won't rust, rot, twist or dent. Choose either a woodgrain or smooth skin, to be painted or stained any colour. Solid fibreglass edges - clean and tidy, which can be trimmed or rebated LVL stiles and rails for superior stability - no warping or bowing Polyfoam resin engineered core for high insulation Better thermal r-rating than aluminium and timber doors High impact surface coating that can be painted or stained
How do I paint or stain my door? See finishing instructions here. Duramax Heritage Entrance Doors Available 1980 x 810/860mm 41mm thick Woodgrain finish only Duramax Modern Entrance Doors Available any size up to 2400 x 1060mm, except FL1S is only available up to 2050 x 860mm. W = woodgrain skin / S = smooth skin FHV WG / FHV SM FVAR10 SM / FVAR10 WG For downloadable specifications, DWG and Revit files, click here. All component sizes - nominal - prior to factory trimming 1980 x 810 x 40, 1980 x 860 x 40 1980 x 400 x 40 1980 x 910, 860, 810, 760, 710, 660, 610, 560, 510, 460, 410 x 35 2400 x 910, 860, 810, 760, 710, 660, 610, 560, 510, 460, 410 x 35 Supplied unfinished and without door furniture. Glass options are additional cost. Solid Core () Ply Faced (2400 x 1200 x 35) Panel (, Vienna, etc) Natural variations in the colour, texture or grain pattern of the wood are not to be considered defects.
Doors must be accorded reasonable treatment by the purchaser and should be stored or hung in dry buildings and not in damp, moist or freshly plastered areas. The utility or structural strength must not be impaired in the fitting of the door, the application of hardware, or cutting and altering of the door for lights, louvers, panels or any special details. A maximum of 3mm may be trimmed from any door edge. Normal “show-through” of frame components in doors shall not be considered a defect. All entrance and solid core must be hinged with three (3) hinges. Entrance doors should be hung in weather protected areas. Doors that are installed in a fully exposed situation including opening out doors will not be warranted unless there is adequate overhead protection. Immediately after fitting, and prior to hanging, the entire door, including the top and bottom edges, must receive two coats of paint, or sealer to prevent absorption of moisture. Semi-gloss or satin finishes are recommended for all doors to reduce “show-through”.
Exterior finishes applied strictly in accordance with manufacturer’s instructions shall be used on entrance doors. Doors exposed to direct weather conditions should be finished with light colours to reduce the risk of heat distortion which may cause warping. Dark may void guarantee. As a guide a dark colour is considered to be a colour with a LRV (Light Reflectance Value) of 0% - 50%, please consult your painter before proceeding. Both faces should have similar colours applied. Regular maintenance should be provided to prevent deterioration. Doors must be inspected upon arrival for visible defects and all claims based there on must be f led within seven (7) days. The manufacturer agrees to repair or replace at its option, unfinished and in the form originally supplied and without charge, any door found to be defective within the meaning of the guarantee. The manufacturer will not be held responsible for additional charges of hanging, painting or other charges arising from the replacement of doors.
Any such defects must be brought to the attention of the manufacturer when discovered and in any event within f ve years from the date of shipment by the manufacturer. The manufacturer is not liable to reimburse any purchaser for doors repaired or replaced without the prior written consent of the manufacturer to such repair or replacement. The manufacturer will not assume responsibility for doors which become defective because of failure to follow these conditions or for hazards of shipment or storage, after doors leave the control of the manufacturer. Considerable damage can occur during the delivery of doors particularly to country areas. “Special Packaging” is recommended (optional extra cost) in an attempt to prevent transit damage. The Company is not responsible for any transit damage. Warp shall be interpreted as meaning the cupping/bowing or twisting of doors. It refers to distortion within the door itself and not its relationship to the jambs or frame in which it is hung.
Warp exceeding 5mm for doors up to 2100 x 920mm and 6mm for doors over 2100 x 920mm and up to 2340 x 920mm shall be considered a defect. Doors in excess of 2340mm high or 1200mm wide are not guaranteed against warp. The guarantee against warp does not apply to the following: a. Doors with face veneers of different species. b. Doors that are improperly hung or do not swing freely. c. External flush doors which have been painted or stained dark , or different each face. Experience has demonstrated that when warp occurs after doors have been delivered to storage or building sites, it is usually due to improper storage or adverse moisture conditions after hanging and not to faulty manufacture. The Company will accept no responsibility for doors when moisture content of the timber falls below 12% or exceeds 18%.The Company will not accept responsibility for conditions wholly beyond its control. However, the Company should be consulted promptly if excessive warping occurs to provide assistance in overcoming the difficulty.